ODROID-N2+ Starter Kit

Beschrijving ODROID-N2+ Starter Kit

Specificaties ODROID-N2+ - 4GB RAM

• Form factor Board
  - Dimensions: 90mm x 90mm x 17mm
  - Heatsink Dimensions: 100mm x 91mm x 18,75mm
  - Weight: 200g including heatsink
• Processor
  - Amlogic S922X Processor (12nm fab)
  - Quad-core Cortex-A73(up to 2.4Ghz) and Dual-core Cortex-A53 (up to 2Ghz)
  - ARMv8-A architecture with Neon and Crypto extensions
  - Mali-G52 GPU with 6 x Execution Engines (800Mhz)
• Memory
  - DDR4 4GiB with 32-bit bus width
  - Data rate: 2640 MT/s (PC4-21333 grade)
  - 1.2Volt low power design
• Storage
  - 1x eMMC connector (8/16/32/64GiB are available)
  - 1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
• Networking
  - 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
  - Realtek RTL8211F (Ethernet transceiver)
  - LED indicators
  * Green LED: Flashing by data traffic at 100Mbps connection
  * Amber LED: Flashing by data traffic at 1000Mbps connection
  - Optional WiFi USB adapters
• Video
  - 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
  - 1 x Composite video (3.5mm jack)
• Audio
  - 1 x Stereo Audio line-out (3.5mm jack
  - 1 x HDMI digital output
  - 1 x Optional SPDIF optical output
• External I/O
  - 4 x USB 3.0 Host ports (shares one single root hub)
  - 1 x USB 2.0 OTG port for Host or Device mode. (No power input)
  - 1 x Debug serial console (UART)
  - 1 x Peripheral Expansion Header (40-pin, 2.54mm pitch)
  2x DC 5V, 2x DC 3.3V, 1x DC 1.8V, 8x GND
  1x SPI
  1x UART
  2x I2C
  25x GPIO (Max)
  2 x ADC input (10bit, 1.8V Max)
  All 3.3V I/O signal level except for ADC input at max 1.8Volt.
• Other features
  - On board RTC(Real Time Clock) IC to keep date and time. A CR2032 coin battery holder was replaced with the 2-pin 1.25mm pitch connector.
  - No battery is included in the board. (CR2032 cell)
  - You can keep the RTC time up to several years with a 200mAh CR2032 battery.
  - 8MiB SPI Flash for boot manager
  - IR receiver for remote controller
  - Built with a large passive heatsink
  System LEDS Indicators:
  - Red (PWR) – Solid light when DC power is connected
  - Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
  Active Cooling Fan Connector (5V 2-pin)
  - Connector (2-pin, 1.25mm pitch)
• Power
  - 1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm
  - DC 7.5V ~ 18V (up to 25W) *** 7.5V ~ 16V from 2022 production (LOT number starts with EL22)
  – DC 12V/2A power adaptor is recommended
  - Power consumption:
  – IDLE : ≃ 2.2W (Performance governor)
  – CPU Stress : ≃ 5.9W (@2016/2208MHz), 6.2W (@2016/2400MHz)
  – Power-off : ≃ 0.2W

Handleiding ODROID N2+